Thermcraft High Temperature Ceramic Electric Heaters

Thermcraft high temperature ceramic heaters are available in two temperature ranges to 1010°C, (1850°F) and to 1204°C, (2200°F). Both flat plate and semi-circular types are offered and can be customized to meet customer specifications. Request our heater brochure for additional ordering information.

Available Types
Standard Heaters
Fibercraft® Heaters

Available Types of Heaters

Ceramic Heaters
Fibercraft® Vacuum Formed Heaters
Plug Heaters
Tubular Heaters
Ceramic Band Heaters
Strip Heaters
Cartridge Heaters
Immersion Heaters
Molydisilicide Heaters
Silicon Carbide
Rod Overbend Heaters
Ribbon-Type Heaters
Platinum or Molybdenum Ceramic Heaters
Metallic Sheath Heaters

High Temperature Ceramic Electric Heaters

High Temperature Ceramic Electrical Heaters

	RL CERAMIC HIGH TEMPERATURE HEATERS 180° semi-cylindrical heaters 1010°C (1850°F) 80-20 Nickel-Chrome wire is helically wound and placed in a grooved ceramic refractory holder. The wire is exposed but can be embedded if required. Leads can be standard (single strand) or braided (two strands twisted). Available with insulation packages, with or with out vestibules. Length can be customized for most application. LINK TO HEATER SPECIFICATION CHART

	RH CERAMIC HIGH TEMPERATURE HEATERS 180° semi-cylindrical heaters 1204°C (2200°F) Iron-Chrome-Aluminum wire is helically wound and placed in a grooved ceramic refractory holder. The coil is embedded with thermal conductive cement, to prevent it from growing out at the grooves due to expansion. Leads can be standard (single strand) or braided (two strands twisted). Available with insulation packages, with or with out vestibules. Length can be customized for most application. LINK TO HEATER SPECIFICATION CHART

	PL CERAMIC HIGH TEMPERATURE HEATERS Flat Plate Heaters (without side flanges) 1010°C (1850°F) FPL CERAMIC HIGH TEMPERATURE HEATERS Flat Plate Heaters (with side flanges) 1010°C (1850°F) 80-20 Nickel-Chrome wire is helically wound and placed in a grooved ceramic refractory holder. The wire is exposed but can be embedded if required. Leads can be standard (single strand) or braided (two strands twisted). Length and wide can be customized for most application. LINK TO HEATER SPECIFICATION CHART

	PH CERAMIC HIGH TEMPERATURE HEATERS Flat plate heaters (without side flanges) 1204°C (2200°F) FPH CERAMIC HIGH TEMPERATURE HEATERS Flat plate heaters (with side flanges) 1204°C (2200°F) Iron-Chrome-Aluminum wire is helically wound and placed in a grooved ceramic refractory holder. The coil is embedded with thermal conductive cement, to prevent it from growing out at the grooves due to expansion. Leads can be standard (single strand) or braided (two strands twisted). Length and wide can be customized for most application. LINK TO HEATER SPECIFICATION CHART

FIBERCRAFT® HIGH TEMPERATURE ELECTRIC HEATERS

FIBERCRAFT® vacuum formed ceramic fiber heaters are a low mass heating system, light weight and with maximum operating temperatures from 1100°C (2012°F) to 1200°C (2192°F). The heaters are manufactured using high quality, high purity ceramic fiber with a low sodium inorganic binder.

The FIBERCRAFT® heater is available in many standard and custom configurations. The following will give you some idea as to the standard units which can be produced by Thermcraft. For the design and engineering of a custom heater please contact the sales office or the representative in your area.

	FIBERCRAFT® 1100°C HEATERS VF-360 These full cylinder Low Mass heater offers faster heat up, greater temperature uniformity, faster recovery rates, and faster cool down time. These heaters use a helically wound iron-chrome-aluminum wire partially embedded in the ceramic fiber. Leads can be standard (single strand) or braided (two strands twisted). The heaters are available with intregal vestibules with the opening sized to meet the need of the application. LINK TO HEATER SPECIFICATION CHART

	VF-180 These half cylinder Low Mass heater offers faster heat up, greater temperature uniformity, faster recovery rates, and faster cool down time. These heaters use a helically wound iron-chrome-aluminum wire partially embedded in the ceramic fiber. The heaters can be used in pairs to surround an existing pipe or tube. Leads can be standard (single strand) or braided (two strands twisted). The heaters are available with intregal vestibules with the opening sized to meet the need of the application. LINK TO HEATER SPECIFICATION CHART

	FIBERCRAFT® 1200°C HEATERS VFR-180 These half cylinder Low Mass heaters use a helically wound iron-chrome-aluminum ribbon partially embedded in the ceramic fiber, and are constructed in order to allow for heat to radiate off in three (3) directions. The heaters can be used in pairs to surround an existing pipe or tube. The heaters are available with intregal vestibules with the opening sized to meet the need of the application. Leads can be standard (single strand) or braided (two strands twisted). LINK TO HEATER SPECIFICATION CHART

	P-VFR Low Mass Plate heater use a helically wound iron-chrome-aluminum ribbon partially embedded in the ceramic fiber, and are constructed in order to allow for heat to radiate off in three (3) directions. Leads can be standard (single strand) or braided (two strands twisted). Length and width can be customized for most applications. LINK TO HEATER SPECIFICATION CHART

	FP-VFR Low Mass Flanged Plate heater use a helically wound iron-chrome-aluminum ribbon partially embedded in the ceramic fiber, and are constructed in order to allow for heat to radiate off in three (3) directions. Leads can be standard (single strand) or braided (two strands twisted). Length and width can be customized for most applications. LINK TO HEATER SPECIFICATION CHART

	THERMCRAFT 12 00°C CAST PLATE HEATERS PH-C The Cast Plate heaters are available in almost any size required for most applications, the large ID groove allow for much larger gage wire there-fore higher watts per square inch of heater surface, then most standard plate heaters. Most options are available on the PH-C, thermocouple holes, braided leads and site ports to name a few. The standard sizes can be found on the chart but almost any reasonable size can be manufactured by THERMCRAFT. LINK TO HEATER SPECIFICATION CHART

	THERMCRAFT 1200°C CAST PLATE HEATERS FPH-C The Flanged Cast Plate heaters are available in almost any size required for most applications, the large ID groove allow for much larger gage wire there for higher watts per square inch of heater surface, then most standard plate heaters. Most options are available on the PH-C, thermocouple holes, braided leads and site ports to name a few. The standard sizes can be found on the chart but almost any reasonable size can be manufactured by THERMCRAFT. LINK TO HEATER SPECIFICATION CHART

	PLUG AIR HEATER THERMCRAFT has the capability to manufacture or rebuild most air heaters used in recirculating ovens. They can also be modified to the highest possible watt output that will still give reliable service. Contact the sales office or the representative in your area.